Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo
In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.
Visualizza gli articoli presentati alla COMSOL Conference 2020
Structural Durability Analysis of Powertrain Mounting Bracket
Structural analysis is performed to check the durability of Engine mounts for a given load and support conditions. The engine mount bracket is subjected to loads primarily due to weight of the powertrain and the unbalanced torque. In this analysis, the component is optimized such that ... Per saperne di più
High Curvature Bending of Ultra-Thin Chips and Chip-on-Foil Assemblies
Ultra-thin chips of less than 20µm become flexible, allowing integration of silicon IC technology with highly flexible electronics. This combination allows for highly intelligent products of unprecedented thinness, flexibility and cost. Examples include sensor systems integrated into ... Per saperne di più
Particle Focusing Optimization and Stress Analysis of a Magnetic Horn
A neutrino oscillation experiment aims to the observation of the transformation of a neutrino of a given flavour into a neutrino of a different flavour. A beam of neutrinos is produced through the decay of charged pions which in turn are produced in the collision of high energy ... Per saperne di più
Fracture on Circuit Board Internal Layers Due to Thermal Stress on Soldered Pins
Circuit board failures are often ignored because they could be impreceptible. This simulation examines how internal layers around a soldered pin via subject to temperature changes during the soldering process are affected, show the forces involved and determine breaking points. A 2D ... Per saperne di più
Residual Stresses and Failure Probability of Solid Oxide Fuel Cells Due to the Sintering Process
A solid oxide fuel cell (SOFC) is composed of four layers (anode, electrolyte compatibility layer and cathode) of different ceramic materials. The anode layer is produced by tape casting, the remaining layers are deposited by screen-printing. The layers are sintered together at high ... Per saperne di più
Simulation of Wear using LiveLink™ for MATLAB®
An incremental wear model has been developed using COMSOL Multiphysics® with MATLAB® to predict the evolution of component geometry as a result of wear. Whilst Archard’s wear law is a well-known empirical model for the prediction of wear volume, the design engineer is interested in ... Per saperne di più
Structural Mechanics for Real Geometry of Basalt Woven Composites
Woven composites with basalt reinforcement plain 1x1 are examined to define structural mechanics. Woven composites were created by the prepreg technology, 8 layers of plain-weave basalt fabrics were saturated by the precursor, polysiloxane matrix Lukosil®, and joint pressed during ... Per saperne di più
Parametric Study of Polyimide - Lead Zirconate Titanate Thin Film Cantilevers for Transducer Applications
The simulation of the piezoelectric actuation of the micro-cantilever is presented. Lead Zirconate Titanate (PZT) was chosen for the device fabrication design, due to its thin film processing flexibility. Four layers compose the cantilever structures presented in this work: PZT ... Per saperne di più
A Concrete Arch Dam under Seismic Loading Conditions
A new regulation for the safety assessment of dams has just been developed in Italy and its approval process is still in progress. As a matter of fact the behaviour of dams under seismic loading conditions is deemed of actual interest due to the recent seismic events occurred. In ... Per saperne di più
High-Intensity Piezo-Ceramic Ultrasonic Transducer with Mechanical Amplifier and Radiation Plate
A COMSOL Multiphysics® model was made to design a mechanical amplifier and radiation plate for the emission of high intensity 40.5 kHz ultrasound to air by means of a Langevin type transducer usually applied in cleaning baths for example. In this work, ultrasonic irradiation is aimed at ... Per saperne di più