Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.


Visualizza gli articoli presentati alla COMSOL Conference 2020

Modelling Waste Water Flow in Hollow Fibre Filters

I. Borsi[1] and A. Fasano[1]
[1]Dipartimento di Matematica U. Dini, Università di Firenze, Firenze, Italy

In this paper we present a model to describe the process of waste water filtration based on hollow-fibre membrane filters. In particular, we deal with membranes whose pores diameter is in the range 0.01-0.1 µm. The main problem in these filtering systems is the membrane fouling. ... Per saperne di più

Transport Phenomena and Shrinkage Modeling During Convective Drying of Vegetables

S. Curcio[1] and M. Aversa[1]
[1]Department of Engineering Modeling, University of Calabria, Arcavacata di Rende, CS, Italy

The aim of the present work is the formulation of a theoretical model describing the transport phenomena involved in food drying process. The attention has been focused on the simultaneous transfer of momentum, heat and mass occurring in a convective drier where hot dry air flows, in ... Per saperne di più

Local Conduction Heat Transfer in U-pipe Borehole Heat Exchangers

J. Acuna[1] and B. Palm[1]

[1]Department of Energy Technology, KTH, Stockholm, Sweden

The most common way to exchange heat with the bedrock in Ground Source Heat Pump (GSHP) applications is circulating a fluid through a U-formed closed loop in vertical boreholes drilled several tenths of meters into the ground. This study presents and compares the results of eight cross ... Per saperne di più

Detection of Magnetic Particles by Magnetoresistive Sensors

A. Weddemann[1], A. Auge[1], F. Wittbracht[1], C. Albon[1], and A. Hütten[1]
[1]Department of Physics, Thin Films and Physics of Nanostructures, Bielefeld University, Bielefeld, Germany

In this work, we demonstrate the implementation of the micromagnetic equations for the description of ferromagnetic thin films in COMSOL Multiphysics®. We apply our model to magnetoresistive sensors consisting of several soft ferromagnetic layers and their response to magnetic particles. ... Per saperne di più

Model of Heat and Mass Transfer with Moving Boundary During Roasting of Meat in Convection-Oven

A.H. Feyissa[1], J. Adler-Nissen[1], and K.V. Gernaey[2]
[1]Food Production Engineering, National Food Institute, Technical University of Denmark, Kgs. Lyngby, Denmark
[2]Department of Chemical and Biochemical Engineering, Technical University of Denmark, Kgs. Lyngby, Denmark

A 2D mathematical model of coupled heat and mass transfer describing oven roasting of meat was formulated from first principles. The current formulation of model equations incorporates the effect of shrinkage phenomena and water holding capacity. The model equations are based on ... Per saperne di più

3D Electro-Thermal Study for Reliability of Automotive Power Vertical MOSFET Using COMSOL Multiphysics®

T. Azoui[1], S. Verde[1][2], J.B. Sauveplane[1], and P. Tounsi[1]
[1]LAAS-CNRS, Toulouse, France
[2]Department of Electronics and Telecommunications Engineering, University of Naples Federico II, Naples, Italy

In this paper 3D electro-thermal FE Model using COMSOL Multiphysics® software of power vertical MOSFET used in the automotive industry is presented. This model is used to analyze the effects of bonding wire lift off defect and to study the influence of metallization thickness and ... Per saperne di più

Thermal Simulation and Package Investigation of Wireless Gas Sensors

A. Paoli[1], L. Seminara[2], D.D. Caviglia[1], A. Garibbo[2], and M. Valle[1]

[1]Department of Biophysical and Electronic Engineering, University of Genova, Genova, Italy
[2]SELEX Communications S.p.A., Genova, Italy

Gas sensor arrays based on metal oxides operating at high temperature are commonly used in many application fields. They can operate on different principles and each sensor may show very different responses to the individual gases in the environment. Data coming from the array can be ... Per saperne di più

Chip Drop After Silver Sintering Process

M.H. Poech[1], M. Weiß[1], and K. Gruber[1]

[1]Fraunhofer Institute for Silicon Technology, Itzehoe, Germany

Since a couple of years, sintering becomes more and more important for power electronics. To press a semiconductor under high temperature in silver paste on a substrate promises benefits for durability. Tests with semiconductors of different thickness expose some problems. After the cool ... Per saperne di più

Multi-Scale Modelling of Catalytic Microreactors

B. Hari[1] and C. Theodoropoulos[1]
[1]The University of Manchester, School of Chemical Engineering and Analytical Science, Manchester, UK

Microreactors are important alternative to conventional reactors in chemistry, chemical, pharmaceutical and semiconductor industries due to their operation characteristics such as increased mass and heat transfer, uniform flow, safety, high throughput through array configurations, ... Per saperne di più

Safe Storage Parameters During CO2 Injection Using Coupled Reservoir-Geomechanical Analysis

T.I. Bjørnarå[1], E. Aker[1], and E. Skurtveit[1]
[1]NGI, Oslo, Norway

Safe short term storage of CO2 depends mainly on structural and solubility trapping. On longer term, mineral trapping is also contributing to the trapping of CO2. To be able to investigate the importance of these different storage mechanisms, a finite element model for simulation of CO2 ... Per saperne di più