Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo
In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.
Visualizza gli articoli presentati alla COMSOL Conference 2020
Photo-bioreactors generate biomass by providing a controlled environment for the cultivation of algae due to photosynthesis. Algae cultivation can be controlled through the operating parameters and bioreactor environment to allow for high productivity and the use of systems with large ... Per saperne di più
A 2nd-generation irradiation target holder is being developed at the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL). This 2nd-generation holder design is focused on improving the loading and unloading of the targets by the HFIR operators since a large number of ... Per saperne di più
铁芯电抗器具有损耗小、噪音低、维护简单、电抗值线性度好、设计寿命长等优点,得到了越来越广泛的应用。但由于电抗器通风散热不良，导致运行中不同程度的局部过热，造成匝间短路、烧损，甚至引起火灾，严重影响电抗器的安全运行。该问题涉及电-磁-热-流体多物理场耦合，电抗器正常运行时电阻损耗和涡流损耗构成主要热源。本文采用COMSOL Multiphysics®多物理场仿真软件，通过AC/DC模块、传热模块、流体模块对铁芯电抗器的电路、磁场、损耗和温升空间分布进行研究。首先施加激励分别得到铁芯、线圈的磁场及损耗密度分布，然后将铁芯及线圈的损耗值添加为插值，作为流场 ... Per saperne di più
Fusion is a form of nuclear energy which has impressive advantages from the point of view of fuel reserves, environmental impact and safety. If successful, fusion energy would ensure a safe, resource conserving, environmentally friendly power supply for future generations. In a world ... Per saperne di più
A laboratory exercise to learn PID controller tuning can be time consuming and taxing on the equipment. A purely equation-based, virtual controller tuning exercise might not seem relevant to real world processes. We have combined a physical process with a COMSOL Multiphysics model to ... Per saperne di più
Electron beam has a wide range of applications in the material processing and joining techniques. Apart from that, it has also been utilized to simulate steady as well as transient fusion reactor relevant heat loads. Transient heat load events spontaneously occur in the fusion reactor. ... Per saperne di più
Tetrafluoroethylene (TFE) is a gas widely employed in industry, which can under specific circumstances experience an exothermic dimerization to octafluorocyclobutane. If the heat generated by this reaction cannot be dissipated to the surroundings, the temperature inside the reactor will ... Per saperne di più
Air pollution caused by particulate matter (PM) is one of the most severe issues in urban environments. Urban green infrastructure (UGI), in particular green walls, have been proven to be capable of capturing PM via deposition on leaves. This phenomenon was assessed by numerical ... Per saperne di più
Optimization of mixing in microfluidic devices is a popular application of computational fluid dynamics software packages, such as COMSOL Multiphysics, with an increasing number of studies being published on the topic. On one hand, the laminar nature of the flow and lack of turbulence in ... Per saperne di più
Hydrogen, the most abundant element in the universe, has great potential as an energy source, and can be generated from renewable energy sources. We used COMSOL for the solution of the energy, mass and momentum balance equations that describe the hydrogen absorption and desorption ... Per saperne di più
