Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo
In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.
Visualizza gli articoli presentati alla COMSOL Conference 2020
Comparison of Borehole Heat Exchangers (BHEs): State of the Art vs. Novel Design Approaches
The efficiency of borehole heat exchangers (BHEs) for geothermal purposes depends not only on material properties but also on their geometrical design. These days most used design consists of two parallel arranged U-shaped pipes which are embedded in a high-conductive shell filling out ... Per saperne di più
Ability of Single-Well Injection-Withdrawal Experiments to Estimate Ground Water Velocity
The authors present a closer look on the Single-Well Injection-Withdrawal Experiment (SWIW) or Push-Pull Experiments and its ability to determine the groundwater velocity, as one of the major parameters concerning reservoir management and underground reservoir characterization. The flow ... Per saperne di più
Simulation of Novel Groundwater Lowering Technique using Arbitrary Lagrangian-Eulerian Method
A novel method for groundwater lowering, which can be applied at construction sites, for aquifer remediation measures or in open mining, is proposed. In contrast to conventional techniques, dewatering is achieved without water conveyance. In this paper the physical concept of the new ... Per saperne di più
Heat Loss Evaluation of an Experimental Set-up for Predicting the Initial Stage of the Boiling Curve for Water at low Pressure
In this paper heat losses and gains are assessed for a specific measuring set-up improving the validity of performance data to accurately predict the initial stage of a boiling curve. Simulation focus on achieving results predicting real measuring data of a plain surface structure. ... Per saperne di più
Effect of Mass Adsorption on a Resonant NEMS
The motion of a resonant NEMS has been widely studied for many different applications such as structural mechanics in engineering, ultra sensitive mass spectrometers or the well known Atomic Force Microscope. The study of the eigenfrequencies of such structures is very important, and ... Per saperne di più
Modelling of a Differential Sensor in Eddy Current Non-destructive Evaluation
Interaction between the probe and a defect in eddy current non-destructive evaluation is studied. Evaluation of sensor signal response is the basis for the calculation. In this work a differential sensor is considered and the problem regarded here is problem 8 from the testing of ... Per saperne di più
Modeling and Simulation of Hydrogen Storage Device for Fuel Cell Plant Using COMSOL Multiphysics
In this work, a 2D dynamic simulation for a portion of metal hydride based hydrogen storage tank was performed using computational software COMSOL 4.0a Multiphysics. The software is used to simulate the diffusion and heating of hydrogen in both radial and axial directions. The model ... Per saperne di più
Transient Modelling of a Fluorine Electrolysis Cell; Fully Coupled Electric Currents, Heat-Transfer, Diluted Species Transport and Laminar Bubbly Flow
A laboratory-scale fluorine reactor was simulated with COMSOL Multiphysics®. This model employs fundamental fully coupled electron-, heat-, mass- and momentum transfer (two-phase) equations to deliver a transient model of the above-mentioned reactor. Quasi-steady-state results were ... Per saperne di più
The Effect of Different Geometries on the Thermal Mantle Convection
For the numerical solving of the equations, Comsol has been applied. Simulations have been modeled in 2D Cartesian, in cylindrical coordinate system and in a “mantle-like” cylindrical-shell. Mantle dynamics is controlled by the Rayleigh number (Ra), which is the ratio of the buoyancy ... Per saperne di più
An Improved Model for High Temperature Inductive Heating
An axially symmetric multiphysics model for industrial induction furnaces has successfully been converted from COMSOL Multiphysics version 3.5a to version 4.2. The model combines computation of magnetic fields, heat transfer and thermal stresses. The inner part of the furnace is ... Per saperne di più