In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

Determination of Fundamental Frequency of a Thin Rectangular Perforated Plate using COMSOL Multiphysics

S. V. N. B. Prasad, and B. Raghavendra

COMSOL Multiphysics 4.0 is being used to simulate the free vibrations of a plate. The results obtained by simulation in COMSOL are in close proximity to that found by Fast Fourier Transform analyzer and analytical method. As of now the vibration analysis of thin rectangular plates with perforations in rectangular pattern has been carried out. The study of vibration analysis of thin ...

Modeling of Limestone Calcination Using Joule Heating

R. Kancharla, and M. Ramakrishna
Padmasri Dr. B.V.Raju Institute of Technology
Medak Dist, AP, India

The limestone calcination reaction is endothermic and will proceed only if the partial pressure of CO2 in the gas above the solid surface is less than the decomposition pressure of the CaCO3. As the reaction is endothermic, the conventional process for calcination uses coal firing in rotary kiln with limestone feed to get the desired temperatures. Microwave heating of limestone is proposed ...

Effect of Bed Diffusion and Operating Parameters on Char Combustion in the Context of Underground Coal Gasification

S. Mahajani, and G. Samdani
Indian Institute of Technology Bombay
Mumbai, India

Char combustion is one of the most important reactions in the process of Underground Coal Gasification (UCG). Experiments are performed in a boat reactor under near isothermal condition to demonstrate effects of heat and mass transfer and bed diffusion through ash layer. To obtain a complete overview of boat experiments and to further get insights, CFD analysis of boat reactor is performed using ...

A MEMS Condenser Microphone for Consumer Applications

S. L. Pinjare, V. S. Nagaraj, S. N. Savitha, S. Kesari, M. S. Sagar, and K. R. Roshan
Nitte Meenakshi Institute of Technology

The MEMS microphone is also called microphone chip or silicon microphone. The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone design. The MEMS microphone has been successfully fabricated and tested in an anechoic chamber. The microphone ...

Finite Element Modeling of Freezing of Coffee Solution

C. Anandharamakrishnan, R. Gopirajah, and N. Chhanwal
Central Food Technological Research Institute
Karnataka, India

Freeze-drying is a popular method of producing shelf stable particulate products and is of particular value for drying thermally sensitive materials (volatiles and biological based), which can be heat damaged by higher temperature methods, such as spray-drying. Porous structures are formed by the creation of ice crystals during the freezing stage, which subsequently sublime during the drying ...

Numerical Study on Mechanical Properties of Stents with Different Materials during Stent Deployment with Balloon Expansion.

P. Ghosh[1], K. DasGupta[1], D. Nag[2], and A. Chanda[1]
[1]School of Bio Science & Engineering, Jadavpur University, Kolkata, West Bengal, India
[2]Mechanical Engineering Department, Jadavpur University, Kolkata, West Bengal, India

The main reason for stent implantation is to provide mechanical support to the arterial wall. So it is important to consider the different mechanical properties of different stent materials while studying the stent implant’s efficacy. The present study gives a comparative overview of mechanical aspects of different stent materials which are most commonly used in angioplasty. Deformation ...

Design, Simulation and Study of MEMS Based Micro-Needles and Micro-Pump for Biomedical Applications

P. K. Podder, D. Mallick, D. P. Samajdar, and A. Bhattacharyya
Institute of Radio Physics and Electronics
University of Calcutta
West Bengal, India

In this paper, we have addressed the issues related to the design and simulation of MEMS based silicon micro-needles for insertion of fluid into the dermis layer and into the subcutaneous fat layer. In addition, a poly-silicon micro-pump based on the principle of electrostatic actuation has been designed and simulated which can be integrated with the proposed micro-needles to control the fluid ...

Two-Dimensional Quasi–Static Analysis For Induction Motor with Faulty Rotor

M. Manna, and S. Miglani
Punjab, India

This paper presents the Finite Element Method technique for predicting performance of Induction motor having Electric and Magnetic asymmetry for rotor cage due to some broken rotor bars. The motor parameters like magnetic vector potential, flux density, surface currents have been determined very precisely by carrying out two dimensional quasi static, transient analysis and by using one of the ...

MEMS Electrostatic Comb Actuator: A Comparison of Different Structure Designs and Materials using COMSOL 3.5a

S. Kapoor[1], D. Aggarwal[2], and A. Gujjar[1]
[1]University Institute of Engineering and Technology, Kurukshetra University, Kurukshetra, Haryana, India.
[2]Electronics Science Department, University Institute of Engineering and Technology, Kurukshetra University, Haryana, India.

The micro machining technology that emerged in the late 1980’s can provide micron sized sensors and actuators. Actuators are used for the transformation of non- mechanical input energy into mechanical output energy. There are many types of micro- actuation mechanisms, most commonly used are piezoelectric, magnetic, thermal, SMA, electrochemical, electrostatic actuation. Electrostatic actuation ...

Numerical Modelling of Wave Propagation in Particulate Composites

P. S. K. Mylavarapu, and S. Boddapati
Defence Metallurgical Research Laboratory

Syntactic foams are hollow particle filled composites that have recently emerged as attractive materials for use in advanced structural applications in aerospace and defence industry. Ultrasonic characterization of these foams is performed extensively in order to understand the effect of porosity and particle size on the ultrasonic properties such as longitudinal velocity and attenuation. ...