Quick Search

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

Optimization Of The Collection Of Sprays By An Enhanced Electronic Sensor

J. Berges[1], B. Barelaud[1], I. Niort[2], and J.L. Decossas[2]
[1]XLIM, Limoges, France
[2]Université de Limoges, France

We propose the study of an electronic sensor allowing the collection of sprays in free space. The detector consists of three elements: a photodiode situated in the center of the structure to which is applied a bias voltage, an aluminum ring which referenced to a voltage higher than that of the photodiode and an insulating material disk (polyvinyl chloride). The total size of the structure is ...

Experimental and Numerical Fluid Flows Study on a X-Millichannel

C. Wolluschek[1], F. Etcheverry[2], M. Cachile[2], and J. Gomba[3]
[1]Mecánica de Fluidos e Ingeniería Térmica, Centro tecnológico Cemitec, Noáin, Navarra, Spain
[2]Grupo de Medios Porosos, Facultad de Ingeniería, UBA, Buenos Aires, Argentina
[3]Instituto de Física Arroyo Seco, UNCPBA, Tandil, Argentina.

In this work, a COMSOL model that predicts velocity and concentration fields inside an X-shaped millichannel (4 mm diameter) is developed. Water and a ink low concentration are injected simultaneously in the two inlets of the device. The mass transfer problem is solved by a Fickian model (solute concentration is low compared with the solvent). The parameters in this study are: initial inlet mass ...

Thermal and Laminar-Fluidic Workbench for a metric Portion of a Gun

M. Brun
Nexter Systems, Versailles, France

Part of a 120mm gun has been represented as a perforated conic iron solid, surrounded by an annular screen. Inside the gun are limit conditions of isolation or thermal flux. The screen is described as a shell, receiving solar heat and exchanging with the outside atmosphere. It bears a defined number of holes on its top and bottom lines, maintaining semi-captive air between itself and the gun. ...

Erosion Of Buffer Caused By Groundwater Leakages Based On ESM-Application

O. Punkkinen[1], A. Jorma[1], K. Kari[2], and M. Olin[3]
[1]B+Tech, Helsinki, Finland
[2]Posiva, Eurajoki, Finland
[3]VTT, Espoo, Finland

In this work the issue of saturation phase erosion caused by groundwater leakages was approached both experimentally and computationally by employing COMSOL\'s Earth Science Module. We evaluated the total mass of eroded bentonite out of a cylindrical erosion channel both numerically and experimentally, and studied its dependence on time. It was observed that logarithmic eroded mass loss as a ...

Analysis Of The Design Criteria For Ancient Greek And Roman Catapults

K.M. Paasch
Center for Product Development, Mads Clausen Institute, South Danish University, Denmark

This paper will give a short overview of use of COMSOL Multiphysics for analyzing ancient Greek and Roman catapults with the main focus on the energy storing torsion springs. Catapults have been known and used in the Greek and Roman world from around 399 BC and a fully standardized design for powerful torsion catapults emerged around 270 BC, based on one basic factor, the diameter of the torsion ...

181 - 185 of 185 First | < Previous | Next > | Last