In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

Improved Perfectly Matched Layers for Acoustic Radiation and Scattering Problems

M. Zampolli[1], N. Malm[2], and A. Tesei[1]
[1]NURC NATO Research Centre, La Spezia, Italy
[2]COMSOL AB, Stockholm, Sweden

Perfectly matched layers (PML) are an efficient alternative for emulating the Sommerfeld radiation condition in the numerical solution of wave radiation and scattering problems. The key ingredient of the PML formulation is the complex scaling function, which controls the anisotropic damping of the PML. The objective of this study is to propose a modified complex scaling function capable of ...

Modeling the Thermally Induced Curvature of Multilayer Coatings with COMSOL MultiphysicsTM

H. Conrad[1], T. Klose[2], T. Sandner[2], D. Jung[1], H. Schenk[2], and H. Lakner[1,2]
[1]Semiconductor and Microsystems Technology Laboratory, Technische Universität Dresden, Germany
[2]Fraunhofer Institute for Photonic Microsystems Dresden, Germany

Within this paper the so called “birth and death” method is demonstrated in use with COMSOL Multiphysics®. With this method the free and reactionless movement of a solid structure on deformed geometries and the activation of this solid structure at later simulation steps is possible. For demonstrating the benefit, this method was applied to simulate the thermal induced ...

Kinetics and Reactor Modeling of Methanol Synthesis from Synthesis Gas

H. Bakhtiary, F. Hayer, H. Venvik, A. Holmen
Norwegian University of Science and Technology Trondheim

Methanol synthesis is a typical reaction in heterogeneous catalysis. In this work, we have studied a laboratory fixed-bed reactor packed with a Cu/Zn/Al2O3 catalyst in both adiabatic and isothermal tubular operational modes. A methanol synthesis kinetic model was implemented in COMSOL Reaction Engineering Lab. Both 1D and 2D pseudo-homogeneous dispersion models were applied to describe the mass ...

Simulation of Production Processes using the Multiphysics Approach: The Electrochemical Machining Process

R. van Tijum
Advanced Technology Center, Philips Consumer Lifestyle, Drachten, The Netherlands

Redmer van Tijum studied Applied Physics at the University of Groningen. In 2006, he received his PhD title on ‘Interface and surface roughness of polymer metal laminates’ in the field of Material Science at the University of Groningen. After that he became research and development engineer at Philips, where he focussed his attention on the improvement of production processes mainly ...

Adaptive Control of Simulated Moving Bed Plants Using Comsol’s Simulink Interface

M. Fütterer
Institut für Automatisierungstechnik, Otto-von-Guericke Universität, Magdeburg, Germany

Preparative chromatography is an important separation method where the simulated moving bed (SMB) technology is an increasingly used separation process for binary mixtures. Several chromatographic columns are arranged in a ring where the feedings and drains are changed cyclically to maintain a continuous separation. For this reason, an adaptive controller is proposed to adjust the flow rates ...

Thermal and Material Flow Modelling of Friction Stir Welding Using COMSOL

H. Schmidt[1,2], and J. Hattel[1]
[1]Technical University of Denmark, Kgs. Lyngby, Denmark
[2]HBS Engineering, Frederiksberg, Denmark

Two friction stir welding models are presented – a global thermal model using the temperature dependent heat source and a local material flow and heat generation model allowing for detailed investigation of different contact conditions. The two models are coupled into a larger local-global model. The flow model includes frictional dissipation from the contact between the work piece and the ...

Advanced Modeling of Friction Stir Welding – Improved Material Model for Aluminum Alloys and Modeling of Different Materials with Different Properties by Using the Level Set Method

S. Dörfler
Wilhelm Gronbach GmbH, Wasserburg a. Inn, Germany

Friction Stir Welding (FSW) has gained much importance throughout the last years. Beside comprehensive experimental work that has been carried out, the simulation of the welding zone is of major interest.  Due to the high strains observed within the welding zone, the Eulerian (CFD) approach seems to be the most promising for the prediction of flow around the FSW tool. However, the CFD ...

Calculation of Cable Parameters for Different Cable Shapes 

H. Lorenzen[1], J. Timmerberg[1], and S. Mylvaganam[2]
[1]Department of Electrical Engineering, UAS OOW, Wilhelmshaven, Germany
[2]Department Technology/Engineering, Telemark University College, Porsgrunn, Norway

Efforts involving simulation of  transmission line networks necessitate the accurate values of the parameters of the lines. In this paper, as an attempt in estimating such parameters, the parameters of high voltage asymmetric power lines are calculated. In the process of estimation, the three phase equivalent circuit model is used. The resistance and inductance of such lines are dependent ...

Validation of DNS Techniques for Dynamic Combined Indoor Air and Constructions Simulations Using an Experimental Scale Model

T. van Goch, and A. van Schijndel
Eindhoven University of Technology, Eindhoven, Netherlands

This paper presents a study on the application of Direct Numerical Solving (DNS) techniques using an experimental scale model. COMSOL Multiphysics is promising in solving dynamic heat and air transport. The experiments can be extremely useful as benchmark for CFD codes.

Optimization of an Electromagnetic Actuator with COMSOL Multiphysics

T. Müller[1], A. Schwenger[2], and H. Haase[1]
[1]Institut für Grundlagen der Elektrotechnik und Messtechnik, Leibniz Universität Hannover, Germany
[2]Volkswagen AG, Germany

This paper describes the automatic optimization of an electromagnetic actuator using a genetic algorithm.  The actuator modeled here is dedicated for charge changing valve actuation in internal combustion engines. In the first step of the simulation, several operating points are calculated using the script language of COMSOL Multiphysics. In order to reduce computation time, only one segment of ...