Menu

Discussion Forum

New Discussion
Filtra

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Large eddy simulation runtime.

Posted 18 nov 2020, 06:58 GMT-5 Computational Fluid Dynamics (CFD), HPC & Cloud Computing Version 5.5 2 Replies

Dan Bence
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Has anyone had experience of running Large Eddy Simulations ? I want to get a sense of how practical it is to run LES simulations in the COMSOL environment. I could not find any examples in the Application Libraries.

I would be grateful if you could share your experience of runtimes, number of elements etc.

Thanks, Dan.

2 Replies Last Post 28 gen 2021, 10:26 GMT-5
COMSOL Moderator

Hello Dan Bence

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.

Sahrish Naqvi
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 22 gen 2021, 12:38 GMT-5

Hi Bence, I also looking for case set up, but could not find it. What about you?

Hi Bence, I also looking for case set up, but could not find it. What about you?
Frank van Gool
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 5 years ago 28 gen 2021, 10:26 GMT-5
Updated: 5 years ago 29 gen 2021, 07:13 GMT-5

I did a quick test with a building simulation, here I choose the following setup:
First realizable k-eps simulation stationary. With 200k elements, 15 minutes on a laptop then switch to LES, SMAGORINSKY
New transient study, initial values from previous simulation. Total length, 1 fluid pass = 300 sec Time step determined from CFL number:
Mesh size around building ±4m; free stream velocity 2 m/s
With a CFL of 0.5, the time step gets me to 1 sec
Solver: Generalized alpha timestepping, manual step of 1 sec. Disable initialisation Total runtime on laptop: 3 hours

The movie below gives some result of the vorticity
For a better results:
- > 2 fluid passes
- a finer mesh
- add turbulence to the inlet

It would be needed to implement an inlet condition based on turbulence, or COMSOL could release a method to deal with this, as in this example the inlet is perfectly smooth.

ps. this is my first test with it, and do not have previous experience in other software with this

I did a quick test with a building simulation, here I choose the following setup: First realizable k-eps simulation stationary. With 200k elements, 15 minutes on a laptop then switch to LES, SMAGORINSKY New transient study, initial values from previous simulation. Total length, 1 fluid pass = 300 sec Time step determined from CFL number: Mesh size around building ±4m; free stream velocity 2 m/s With a CFL of 0.5, the time step gets me to 1 sec Solver: Generalized alpha timestepping, manual step of 1 sec. Disable initialisation Total runtime on laptop: 3 hours The movie below gives some result of the vorticity For a better results: - > 2 fluid passes - a finer mesh - add turbulence to the inlet It would be needed to implement an inlet condition based on turbulence, or COMSOL could release a method to deal with this, as in this example the inlet is perfectly smooth. ps. this is my first test with it, and do not have previous experience in other software with this

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content