Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.


Visualizza gli articoli presentati alla COMSOL Conference 2020

MEMS and Nanotechnologyx

Simulation of Deformed Solid Particles in Constrained Microfluidic Channel

M. Cartas-Ayala[1], R. Karnik[1]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA

Characterization of particles has numerous applications in science and diagnostics. Recently, particle passage through constrained microchannels has been proposed to characterize particles based on their passage velocity. Nevertheless, there is no clear understanding of how the physics ... Per saperne di più

Electromagnetic Release Process for Flexible Electronics

G. Coryell[1][,][2]
[1]School for Engineering of Matter, Transport, and Energy, Arizona State University, Tempe, AZ, USA
[2]Chemistry Department, United States Naval Academy, Annapolis, MD, USA

Flexible electronics are temporarily affixed to a rigid carrier such as glass or silicon prior to device fabrication to facilitate robotic handling of the device, but also to allow optical lithography to stay within overlay design registration budget; without the rigid carrier, a ... Per saperne di più

COMSOL Thermal Model for a Heated Neural Micro-Probe

M. Christian[1], S. Firebaugh[1], A. Smith[1]
[1]United States Naval Academy, Annapolis, MD, USA

This project utilizes the heat transfer module of the COMSOL Multiphysics environment to model the effects that an ohmic heating probe will have on neural tissue. The model quantifies the thermal impact of active components embedded on a neural micro probe by solving the Penne’s bioheat ... Per saperne di più

Modeling Void Drainage with Thin Film Dynamics

J.J. Gangloff Jr.[1], W.R. Hwang[2], S.G. Advani[1]
[1]Center for Composite Materials, Department of Mechanical Engineering, University of Delaware, Newark, DE, USA
[2]School of Mechanical Engineering, Gyeongsang National University, Jinju, Gyeongsangnam-do, Korea

Voids in composite materials can lead to degraded structural performance. The following is a study of voids or bubbles in uncured viscous polymer resin during composites processing. The goal is to determine if voids can successfully migrate towards vacuum pathways, coalesce with the ... Per saperne di più

Computational Analysis of Evaporation in Tailored Microchannel Evaporators

S. Arslan[1], J. Brown[1]
[1]Lawrence Technological University, Southfield, MI, USA

The rapid increase in power densities of integrated circuits has induced a significant interest in new reliable and high heat flux cooling technologies. The implication of such growth is the increased need for more efficient and more compact cooling mechanisms. Promising research has ... Per saperne di più

Passive Microsensor Based on LC Resonators for Substance Identification

D.A. Sanz Becerra[1], E.A. Unigarro Calpa[1], J. Osma[1], F. Segura[1]
[1]Universidad de los Andes, Bogotá, Colombia

A scheme for inductive wireless powering and readout of passive LC sensor is presented. The sensor’s inductor is designed as a planar square coil and is used as the power receiving component. The capacitor is connected directly to the inductor and it was designed as an interdigital ... Per saperne di più

Simulation and Fabrication of Wireless Passive MEMS Pressure Sensor

E.A. Unigarro Calpa[1], D.A. Sanz Becerra[1], A. Arciniegas[2], F. Ramirez[1], F. Segura-Quijano[1]
[1]Universidad de los Andes, Bogotá, Colombia
[2]Instituto Barraquer de América, Bogotá, Colombia

A wireless passive pressure sensor and the measurement system were design and simulated using COMSOL 4.3. The sensor is based on MEMS capacitor attached to a planar inductor for wireless powering and readout. An external coil is used for the measuring system. The pressure to be measured ... Per saperne di più

The Effects of the Electrical Double Layer on Giant Ionic Currents through Single Walled Carbon Nanotubes

G. Zhang[1][,][2][,][3], S.L. Bearden [1]
[1]Department of Bioengineering, Clemson University, Clemson, SC, USA
[2]Department of Electrical and Computer Engineering, Clemson University, Clemson, SC, USA
[3]Institute for Biological Interfaces of Engineering, Clemson University, Clemson, SC, USA

Electrofluidic transport through a single walled carbon nanotube (SWCNT) is enhanced by electroosmosis. Electroosmosis is made possible in these devices by the combination of a large slip length within SWCNTs and the interfacial potential at the solution/nanotube interface. A ... Per saperne di più

Surface Plasmon Resonance

J. Crompton[1], S. Yushanov[1], L.T. Gritter[1], K.C. Koppenhoefer[1]
[1]AltaSim Technologies, Columbus, OH, USA

The resonance conditions for surface plasmons are influenced by the type and amount of material on a surface. Full insight into surface plasmon resonance requires quantum mechanics considerations. However, it can be also described in terms of classical electromagnetic theory by ... Per saperne di più

Modeling and Prediction of Line Pattern Collapse

D. Bassett[1], M. Carcasi[1], W. Printz[1]
[1]Tokyo Electron America, Austin, TX, USA

In semiconductor manufacturing, effective cleaning of structures with liquid is one of the most important and potentially difficult process steps. It is important because it remains the cheapest and most cost-effective method to remove particles and residues from the structures in order ... Per saperne di più