Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.


Visualizza gli articoli presentati alla COMSOL Conference 2020

AC/DC Electromagneticsx

Analysis of a Prototype MRI Hybrid Birdcage RF Coil with Uncertainty Quantification (*)

J. T. Fong [1],
[1] National Institute of Standards & Technology, Gaithersbug, MD, USA

INTRODUCTION. In a magnetic resonance imaging (MRI) system (see Fig. 1), it is necessary to excite the nuclei of a patient into coherent precession for imaging. This requires coupling between the nuclei and a source of radio frequency (RF) power (the transmitter). To receive a ... Per saperne di più

Maximizing the Fatigue Crack Response in Surface Eddy Current Inspections of Aircraft Structures

C. Mandache [1], T. Theodoulidis [2],
[1] National Research Council Canada, Ottawa, ON, Canada
[2] University of Western Macedonia, Kozani, Western Macedonia, Greece

In-service detection of fatigue cracking in metallic aerospace structures relies on capable and efficient eddy current inspection procedures. For best results, inspections with surface scanning eddy current techniques are following rigorous procedures that indicate the instrument ... Per saperne di più

Genetic Algorithm for Geometry Optimization of Optical Antennas

R. Diaz de Leon [1], G. Gonzalez [1], A. G. Rodriguez [1], E. Flores [2], F. J. Gonzalez [1],
[1] Universidad Autonoma de SLP, San Luis Potosi, S.L.P., Mexico
[2] Instituto Tecnologico de SLP, San Luis Potosi, S.L.P., Mexico

A genetic algorithm was programmed in MATLAB® software and linked to the COMSOL Multiphysics® software with the COMSOL LiveLink™ for MATLAB® to optimize the geometry of an optical antenna (nanoantenna). The proposed computational model demonstrated that nanoantenna geometries does not ... Per saperne di più

FEM Analysis and Optimization of Electro-Stimulating Implants for Bone Regeneration and Prevention of Bacterial Infection

T. Bender [1], J. Ziebart [2], T. J. Dauben [1], B. Kreikemeyer [3], R. Bader [2]
[1] Institute of Medical Microbiology, Virology and Hygiene, Rostock University Medical Center, Rostock, Germany; Research Laboratory for Biomechanics and Implant Technology, Department of Orthopedics, Rostock University Medical Center, Rostock, Germany
[2] Research Laboratory for Biomechanics and Implant Technology, Department of Orthopedics, Rostock University Medical Center, Rostock, Germany
[3] Institute of Medical Microbiology, Virology and Hygiene, Rostock University Medical Center, Rostock, Germany

The aim of this study is to investigate the influence of electro-magnetic stimulation on bone regeneration and the effect on bacterial infection. Electro-magnetic stimulation is a promising technique and a powerful tool for the enhancement of bone regeneration. To optimize the amplitude ... Per saperne di più

Novel Automated Software System for Arcing Simulation in Spacecraft On-Board Electronics

V. Kozhevnikov [1], V. Karaban [2], D. Kosov [2], A. Kozyrev [1], A. Batrakov [1], N. Semeniuk [1], L. Zjulkova [1]
[1] Institute of High Current Electronics, Tomsk, Russia
[2] Tomsk State University of Control Systems and Radioelectronics, Tomsk, Russia

In our project, we propose an innovative software solution to the problem of electrical arcing risk prediction in high-voltage on-board electronic equipment intended for long-term self-contained use, e.g. in spacecraft conditions. It completely based on so-called “decomposition” approach ... Per saperne di più

Thermal Analysis on Module Level in an Automotive Battery Package

Z. Wu [1], H. Kemper [1],
[1] Energy Storage Systems, FH Aachen, Aachen, Germany

Vehicles with battery as energy storage fascinate more and more people. Meanwhile, more questions are surfaced – How to ensure a safe operation of the battery package? How long could the cycle life of a battery package reach? Can a battery package be operated in any environmental ... Per saperne di più

Simulation of Electro-Thermal Transients in Superconducting Accelerator Magnets

L. Bortot [1], M. Maciejewski [2], M. Prioli [1], B. Auchmann [3],
[1] CERN, Geneva, Switzerland
[2] CERN, Geneva, Switzerland; Lodz University of Technology, Lodz, Poland
[3] CERN, Geneva, Switzerland; Paul Scherrer Institute, Zurich, Switzerland

The paper presents the application of COMSOL Multiphysics® software to the modelling of superconducting accelerator magnets. A 2D magneto-thermal model is developed, using an equivalent magnetization formulation to take into account the eddy-currents’ effects. Due to the model ... Per saperne di più

3D FEM-Simulation of Magnetic Shape Memory Actuators

M. Schautzgy [1], U. Kosiedowski [2], T. Schiepp [3],
[1] ETO MAGNETIC GmbH, Stockach, Baden-Württemberg, Germany ; Department of Mechanical Engineering, HTWG Konstanz, Konstanz, Baden-Württemberg, Germany
[2] Department of Mechanical Engineering, HTWG Konstanz, Konstanz, Baden-Württemberg, Germany
[3] ETO MAGNETIC GmbH, Stockach, Baden-Württemberg, Germany

Electromagnetic actuators are a well-known field where finite element simulations are applied. Magnetic Shape Memory (MSM) actuators represent a new type of smart electromagnetic actuators where the MSM material elongates and contracts when applying a magnetic field. The MSM material ... Per saperne di più

An App for Calculating the Electric Field outside Electrical Installations

N. Lavesson [1],
[1] ABB Corporate Research, Västerås, Sweden

This paper describes the implementation of an app for calculating low frequency electric fields outside electrical installations. The app is based on a 2D parametric geometry chosen in such a way that it approximates a large class of electrical installations, which consist of a tower or ... Per saperne di più

Transient Simulation of an Electrochemical Machining Process for Stamping and Extrusion Dies

M. Penzel [1], M. Hackert-Oschätzchen [2], M. Kreißig [1], M. Kowalick [1], M. Zinecker [1], A. Schubert [1], G. Meichsner [3],
[1] Professorship Micromanufacturing Technology, Technische Universität Chemnitz, Chemnitz, Germany
[2] Professorship Micromanufacturing Technology, Technische Universität Chemnitz, Chemnitz, Germany; Fraunhofer Institute for Machine Tools and Forming Technology, Chemnitz, Germany
[3] Fraunhofer Institute for Machine Tools and Forming Technology, Chemnitz, Germany

Precise electrochemical machining (PEM) is a non-conventional machining technology, based on anodic dissolution of metallic work-pieces. In this study an additional extension of the precise electrochemical machining with a precise angle-controlled cylinder positioning is aimed. Due to ... Per saperne di più