a_bs_ib_i 0 ""
ab_ib_i 30[deg] "Bending angle of folded section"
ac_h_s_ib_i 30 "Shear angle, back of c-shape blades"
ac_ib_i 30 "Vertical angle between arm and c-shaped blade"
ac_s_ib_i 30 ""
ac_s_ib_ib 30[deg] "Internal angle, c-shaped profile"
ap_ib_i 45 "Pitch angle of impeller blade"
ar_ib_i 0 "Rake angle of impeller"
as_ib_i 240[deg] "Relative rotation angle around shaft"
bo_rd_ta_i (1/10)[1] "Bottom offset of rotating domain relative to the tank bottom minor radius"
d_a_ib_i 0.12[m] "Diameter of attachment section"
d_cs_im_i 1.05*d_im_i "Control surface diameter"
d_hu_i 0.1 "Impeller hub diameter"
d_id_i 0.45[m] "Diameter of impeller dish"
d_im_i 0.7[m] "Impeller diameter"
d_is_i 0.05[m] "Impeller shaft diameter"
d_ta_i 1.9[m] "Tank diameter"
Da d_im_i "Input diameter for turbulence model"
db_im_i 0.3[m] "Distance of first impeller hub from bottom"
dc_ib_i 0.08 "Blade width, c-shaped blades"
density 1e3 "Fluid density"
h_an_im_i 0.6[m] "Height of anchor impeller"
H_mesh 0.05[m] "Mesh parameter"
h_ta_i 2.5[m] "Tank height"
hc_ta_i 0.3[m] "Height of cone section"
hp_im_i 1.85[m] "Impeller position"
hp_is_i 0[m] "Position of the lowest part of the impeller shaft"
hp_ta_i 0[m] "Tank position along the z-axis"
l_ib_i 0.15[m] "Length of the impeller blades, Rushton, Smith"
l_is_i 2.2[m] "Impeller shaft length"
lc_ib_i 0.08 "Blade length, c-shaped blades"
lr_bu_ib_i 0.3[1] "Relative position of the bending point along the length of the upper edge of the impeller blade"
lr_cl_ib_i 0.5[1] "Relative position of cutting point along the length of the lower edge"
lr_cu_ib_i 0.5[1] "Relative position of cutting point along the length of the upper edge"
miu viscosity "Input viscosity"
n_ba_i 0 "Number of baffles"
n_ib_i 3[1] "Number of blades"
off 0[1] ""
Omega (rpm*2*pi[rad]) "Angular velocity"
on 1[1] ""
pa_cs_im_i 1 "Parameter that adds control surfaces around the impellers (= 1 on, = 0 off)"
pa_rd_im_i 1 "Parameter that controls the impeller blade direction, 1 = clockwise and -1 = counterclockwise"
pa_ud_im_i off "Flip impeller vertically"
rc_h_ib_i 0.3[m] "Curvature of backswept Rushton, Smith, and Backswept impeller"
rc_v_ib_i 0.15[m] "Hydrofoil curvature radius closest to the hub"
rf_ib_i 0.02[m] "Fillet radius of outer vertices"
rf_ta_i 0.1[m] "Fillet radius for lower tank edge for flat bottomed tank"
rho density "Input density"
rm_b_ta_i 0.3[m] "Radius of dished section for dished bottom tank"
rmi_an_im_i 0.25[m] "Minor radius of anchor impeller"
rpm 120[1/min] "Revolutions per minute"
sigma 0.072[N/m] "Surface tension of the fluid"
theta 0*(pi/2)[rad] ""
TIME 0[s] ""
viscosity 1e-3 "Fluid viscosity"
w_a_ib_i 0.05[m] "Blade attachment width"
w_ba_i 0.2 "Baffle width"
w_bou_ib_i 0.075[m] "Width of the folded section at the outer edge"
w_cil_ib_i 0[m] "Width of inner and lower cut"
w_ciu_ib_i 0.025[m] "Width of inner and upper cut"
w_col_ib_i 0.075[m] "Width of outer and lower cut"
w_cou_ib_i 0[m] "Width of outer and upper cut"
w_ib_i 0.08 "Impeller blade width"
w_o_ib_i 0.05 "Outer impeller width"
wc_ib_i 0.08 "Blade distance, c-shaped blades"
wr_ai_ib_i 0.5[1] "Ratio between blade width and blade attachment"
wr_asu_ib_i 1 "Asymmetry factor for upper part of the width of the impeller blade: 1 = symmetry, >1 = wider upper part"
wr_io_ib_i 0.6 ""