Presentazioni e Articoli Tecnici

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

On the Convergence Order of COMSOL Solutions

A. Bradji1, and E. Holzbecher2
1Charles University, Prague, Czech Republic
2Weierstrass Institute for Applied Analysis and Stochastics WIAS, Berlin, Germany

The convergence of numerical solutions is mainly determined by the convergence order, which quantifies the improvement of the solution when the mesh is refined. In this paper we examine various differential equations and the convergence behavior of their COMSOL Finite Element solutions. The numerically observed convergence rates are compared with theoretical results, as far as these are ...

Undergraduate Studies of Supersonic Flow from a Converging-Diverging Nozzle

K. Stein[1], N. Gessner[1], R. Peterson[1], A. Wiedmann[1]
[1]Department of Physics, Bethel University, St. Paul, MN, USA

Undergraduate studies are carried out to examine the supersonic flow from an axisymmetric converging-diverging nozzle. Flow in the nozzle is initiated by the rupture of a diaphragm that is positioned between the nozzle and a 1-gallon pressurized air tank. Simulations are carried out in COMSOL Multiphysics® for unsteady, axisymmetric flow with the High Mach Number interface of the CFD Module. ...

Modeling of Active Infrared Thermography for Defect Detection in Concrete Structures

S. Carcangiu[1], B. Cannas[1], G. Concu[2], N. Trulli[3]
[1]Department of Electric and Electronic Engineering, University of Cagliari, Cagliari, Italy
[2]Department of Civil Engineering, Environmental and Architecture, University of Cagliari, Cagliari, Italy
[3]Department of Architecture and Planning, University of Sassari, Alghero, Italy

An experimental program has been developed, with the purpose of evaluating the reliability in building diagnosis and characterization of an integrated analysis of several parameters related to heat transfer process through the building material. The Infrared Thermography Technique (IRT) has been applied. Experimental measurements have been carried out on a concrete structure with an inside ...

Simulation Organogenesis in COMSOL: Deforming and Interacting Domains

D. Iber[1], D. Menshykau[1]
[1]D-BSSE, ETH Zurich, Basel, Switzerland

Organogenesis is a tightly regulated process that has been studied experimentally for decades. We are developing mechanistic models for the morphogenesis of limbs, lungs, and kidneys with a view to integrate available knowledge and to better understand the underlying regulatory logic. Organ size changes dramatically during development, and tissues are composed of several layers that may expand ...

Food Cooking Process. Numerical Simulation of the Transport Phenomena

B. Bisceglia[1], A. Brasiello[1], R. Pappacena[1], R. Vietri[1]
[1]University of Salerno, Department of Industrial Engineering, Fisciano (SA), Italy

Aim of the study is to determine the influence of some of the most important operating variables, especially humidity and temperature, of drying air on the performance of cooking process of pork meat. The process is simulated using finite elements software COMSOL Multiphysics®. The proposed model considers two geometries: cylindrical and parallelepiped, with fixed physical properties and ...

The Influence of Core Shape and Material Nonlinearities to Corner Losses of Inductive Element

M. Puskarczyk[1], B. Jamieson[1], W. Jurczak[1]
[1]ABB Corporate Research Center, Kraków, Poland

The effects of sharp corners on the flux distribution in a ferromagnetic core are modeled using COMSOL Multiphysics® to determine the time-domain flux density for an applied field which is uniform in the non-corner section of the core. The frequency spectrum of the flux distribution is calculated for testing points through the corner and the effects of harmonic frequencies on the flux and loss ...

Modeling Linear Viscoelasticity in Glassy Polymers using Standard Rheological Models

M. Haghighi-Yazdi, and P. Lee-Sullivan
University of Waterloo
Waterloo, ON
Canada

In this study, a capability has been developed for modeling the linear viscoelastic behaviour of a glassy polymer using COMSOL Multiphysics®. The two rheological models by Maxwell and Kelvin-Voigt were used for modeling stress relaxation and creep loading behavior, respectively, of a typical gas pipe under two modes of plane stress and plane strain. An advantage of the developed model is its ...

Simulation of MEMS based Flexible Flow Sensor for Biomedical Application

D. Maji[1], C. P. Ravikumar[2], and S. Das[1]
[1]School of Medical Science and Technology, Indian Institute of Technology, Kharagpur, West Bengal, India
[2]Texas Instruments (India) Pvt. Ltd., Bangalore, India

Arterial disease, especially Coronary Artery Disease (CAD) is one of the leading causes of premature morbidity and mortality. During the flow, blood interacts with vessel wall mechanically and chemically which modulates the plaque formation in blood vessel leading to coronary artery diseases. Here we propose to simulate a MEMS based flexible flow sensor based on anemometer principle designed to ...

Harmonic Simulation of Viscoelastic Polymer Microcantilever for Electrostrictive Energy Harvesters

N. Alcheikh[1], C. Ayela[1], I. Dufour[1]
[1]Univ. Bordeaux, IMS Lab, Pessac, France.

Electrostrictive polymers have been of significant interest over the last years for energy harvesting. Principle is based on the conversion of a mechanical deformation into electricity. The stored energy basically depends on the mechanical strain induced into an electrostrictive polymer by the mechanical resonant vibration of a microcantilever supporting the electrostrictive layer. In this work, ...

Moisture Risks in Multi-layered Walls - Comparison of COMSOL Multiphysics® and WUFI®PLUS Models with Experimental Results

A. Ozolins[1], A. Jakovics[1]
[1]Laboratory for Mathematical Modelling of Technological and Environmental Processes, Riga, Latvia

Moisture can cause serious damages in different building components therefore the heat and moisture calculation in building constructions are important tasks. In the current paper, two different multi-layered walls, mainly consisted of wooden materials and mineral wool, are analyzed. Risks of mould growth under Latvian climate conditions are estimated using 3 different approaches: experimental ...

Quick Search