Presentazioni e Articoli Tecnici

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

Theory of Proportional Solenoids and Magnetic Force Calculation Using COMSOL Multiphysics

O. Vogel, and J. Ulm
Heilbronn University
Campus Künzelsau
Künzelsau, Germany

Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...

Lamb Waves and Dispersion Curves in Plates and It’s Applications in NDE Experiences Using Comsol Multiphysics

P. Gómez, J. P. Fernandez, and P. D. García
Hydro-Geophysics & NDE Modeling Unit
University of Oviedo
Mieres, Spain

In this paper, a model for numerically obtaining lamb wave modes and dispersion curves in plates is presented. It is shown that COMSOL Multiphysics can be employed to simulate the behavior of guided waves in dispersive plates, which is useful for NDE applications. A two dimensional steel plate (4x0.1 meters) is excited with a space-time impact point source. To model the point source, we use ...

Microfluidic Systems for Cell Growth and Cell Migration Studies

M.Dimaki[1], P. Shah[1], D. Kwasny[1], J. Lange Moresco[2], and W. E. Svendsen[1]
[1]Department of Micro- and Nanotechnology, Technical University of Denmark, Lyngby, Denmark
[2]Sunstone Capital, Copenhagen, Denmark

Lab-on-a-chip devices for cell culturing are becoming imperative in order to satisfy the needs for point-of-care or decentralized laboratory testing. Towards that goal we have developed miniaturized membrane based cell culture chambers for use within the field of chromosome analysis. The same principle was applied for the development of a miniaturized cell migration device. Flow and ...

Excimer Laser-Annealing of Amorphous Silicon Layers

J. Förster, and H. Vogt
Institute of Electronic Components and Circuits
University Duisburg-Essen
Duisburg, Germany

A one-dimensional model of Excimer Laser-Annealing of amorphous silicon layers which are irradiated with a KrF excimer laser is described. For realisation, the application mode heat transfer in solids is used. The model predicts a melt threshold for the energy density of the laser of 88.5 mJ/cm^2. It also predicts a linear increase of the melt duration with a slope of approximately 625 ...

Analysis Of Linearly Polarized Modes

I. Avram, and I. Gavril Tarnovan
The Technical University of Cluj Napoca
Cluj, Romania

This paper presents a study on the propagation modes of electromagnetic waves through a step index fiber optics. To analyze the propagation of electromagnetic field, a simulation in Comsol 4.0 has been implemented using two different optical fibers. Obtaining the propagation modes, called linearly polarized modes (LPnm) to get their characterization according to the radial and azimuthal ...

Transient Modelling of a Fluorine Electrolysis Cell; Fully Coupled Electric Currents, Heat-Transfer, Diluted Species Transport and Laminar Bubbly Flow

R. Pretorius[1], P. L. Crouse[1], and C. J. Hattingh[2]
[1]University of Pretoria, Pretoria, Gauteng, South Africa
[2]Metallurgical Testing and Consultation (MTC) cc, Farrarmere, South Africa

A laboratory-scale fluorine reactor was simulated with COMSOL Multiphysics®. This model employs fundamental fully coupled electron-, heat-, mass- and momentum transfer (two-phase) equations to deliver a transient model of the above-mentioned reactor. Quasi-steady-state results were produced for the current density, electric field, temperature, reactive species concentration, gas- and liquid ...

Modeling and Simulation of Hydrogen Storage Device for Fuel Cell Plant Using COMSOL Multiphysics

O. Akanji, and A. Kolesnikov
Department of Chemical & Metallurgical Engineering
Tshwane University of Technolgy
Pretoria, South Africa

In this work, a 2D dynamic simulation for a portion of metal hydride based hydrogen storage tank was performed using computational software COMSOL 4.0a Multiphysics. The software is used to simulate the diffusion and heating of hydrogen in both radial and axial directions. The model consists of a system of partial differential equations (PDE) describing two dimensional heat and mass transfer of ...

Current Distribution and Magnetic Fields in Complex Structures Using Comsol Multiphysics

S. F. Madsen, and C. Falkenstrøm Mieritz
Highvoltage.dk ApS
Lejre, Denmark

The present paper presents numerical calculations of the magnetic fields and the current distribution within a wind turbine nacelle. The results are used by control system engineers designing panels and cables, who must ensure that the immunity of the equipment complies with the environment within the turbine. Since the release of the International standard concerning lightning protection of ...

Transient Electromagnetic-Thermal FE-Model of a SPICE-Coupled Transformer Including Eddy Currents with COMSOL Multiphysics 4.2

H. Neubert[1], R. Disselnkötter[2], and T. Bödrich[1]
[1]Technische Universität Dresden, Institute of Electromechanical and Electronic Design, Dresden, Germany
[2]ABB AG, Forschungszentrum Deutschland, Ladenburg, Germany

Current transformers are used to measure currents in power grid systems. They are characterized by strong interactions between external electrical sources and loads respectively and the magnetic subsystem. Self-heating due to losses has to be considered because of the temperature-dependent material behaviour. The paper presents a transient 3D FEA transformer model which includes a H(|B|) ...

Analysis of a Three-phase Transformer Using COMSOL Multiphysics and a Virtual Reality Environment

A.Buchau, and W. M. Rucker
Institut für Theorie der Elektrotechnik
Universität Stuttgart
Stuttgart, Germany

The simulation software COMSOL Multiphysics is applied to the numerical com-putation of the magnetic fields of a three-phase transformer. A three-dimensional model of the geometrical configuration is created with the help of the CAD tools of COMSOL Multiphysics. There, all dimensions of the transformer are defined by parameters. The creation of an optimal finite element mesh is improved by some ...

Quick Search

1 - 10 of 186 First | < Previous | Next > | Last