Scopri come la simulazione multifisica viene utilizzata per ricerca e sviluppo

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.


Visualizza gli articoli presentati alla COMSOL Conference 2020

2011 - Bangalorex

Effect of Channel Width on Fuel Cell Performance Using 3D Modelling

R. Pushpangadan, S. S. Dimble, and S. P. Duttagupta
IIT Bombay
Mumbai
Maharasthra, India

A three Dimensional model of the PEM Fuel cell is implemented using COMSOL Multiphysics and the channel width is varied to study the performance.Effect of channel width on the performance of the cell is studied by varying the width of the channel and keeping channel width to rib ratio ... Per saperne di più

Two-Dimensional Quasi–Static Analysis For Induction Motor with Faulty Rotor

M. Manna, and S. Miglani
SLIET
Sangrur
Punjab, India

This paper presents the Finite Element Method technique for predicting performance of Induction motor having Electric and Magnetic asymmetry for rotor cage due to some broken rotor bars. The motor parameters like magnetic vector potential, flux density, surface currents have been ... Per saperne di più

Optimized Design of Shielded Microstrip Lines using Adaptive Finite Element Method

P. Kakria[1], A. Marwaha[1], and M. S. Manna[2]
[1]Electronics & Communication department, SLIET Longowal, Distt. Sangrur, Punjab, India.
[2]Electrical & Instrumentation department, SLIET Longowal, Distt. Sangrur, Punjab, India.

In this paper, the attempt has been made to design and analyze single strip shielded Microstrip line with capacitive coupling. The main objective is to compute the capacitance per unit length of shielded Microstrip line using Finite Element technique. The computational and simulation ... Per saperne di più

Finite Element Analysis of Curved Cone Corrugated Ground Plane Conical Antenna

R. Sharma, and A. Marwaha
SLIET, Longowal, Sangrur
Punjab, India

Curved cone corrugated ground plane conical antenna has been designed and analyzed using Finite Element Method. In this paper, we introduce a novel Curved cone corrugated ground plane conical antenna for ultra-wideband (UWB) applications. The antenna is composed of curved cone with ... Per saperne di più

Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method

M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Dhaka, Bangladesh

Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic ... Per saperne di più

Simulation Based Approach to Fluorescence Diffuse Optical Tomography

R. Singh, and I. Jose
BITS Pilani Goa Campus
Goa, India

Diffuse Optical Tomography (DOT) uses Near Infra-red (NIR) light to monitor physiological changes in internal organs. NIR light being less energetic in nature can be used for continuous monitoring of tumor infected biological tissue, neonatal brain and many such applications where high ... Per saperne di più

Simulations of Polymer Based Micro Heater Operated at Low Voltage

M. Gayake[1], D. Bodas[2], and S. A. Gangal[1]
[1]Department of Electronic science, University of Pune, India
[2]Centre for Nanobioscience, Agharkar Research Institute, India

This paper presents a design of polymer based micro heater operating in the temperature range of 200- 250°C which could be operated at low voltage (battery operated). The micro heater has been designed and simulated using COMSOL 4.1, FEM simulation tool. Simulation was performed for ... Per saperne di più

Analysis and Optimization of Dual Arm, Center Excited, Surface Micro-machined Archimedean Spiral Antenna with Improved Wideband Characterestics

G. Miranda[1], N. S. Pamidighantam[1], R. V. Iyer[2], S. Shukla[3], P. Suresh[3], and P. M. Soundarajan[3]
[1]Department of Telecommunications, PESIT, Bangalore,Karnataka,India
[2]Department of Science and Humanities, PESIT, Bangalore,Karnataka,India
[3]DARE,Bangalore,Karnataka,India

An Archimedean Spiral antenna is the common frequency independent antenna which have very large bandwidth. Archimedean Spiral antenna are circularly polarized and typically have radiation patterns with peaks perpendicular to the plane of the spiral. Micro-machining techniques improves ... Per saperne di più

On the Simulation of Electromagnetic Forming Process of a Tube using Multiphysics Software

S. Gawade[1], P. P. Date[2], and S. B. Sharma[1]
[1]Production Engineering. Dept. SGGS IE&T, Nanded, India
[2]Mechanical Engineering. Dept, IIT, Bombay, India

Electromagnetic forming (EMF) is a typical high speed forming process using the energy density of a pulsed magnetic field to form workpieces made of metals with high electrical conductivity like e.g. aluminium. This forming process can be very advantageous as compared to conventional ... Per saperne di più

Structured Ultrasonic Metasurfaces

R. C. Thiagarajan
ATOA Scientific Technologies Private Limited
Bangalore, India

Ultrasonic acoustic waves usually encounter interfaces with significant impedance mismatch in practical medical or industrial imaging applications. A transparent interface can help to improve the performance of medical and industrial imaging and overall innovative applications. ... Per saperne di più