C. Caruso, P. Lonetti, and A. Manna
Department of Structural Engineering, University of Calabria, Arcavacata di Rende, CS, Italy
A generalized model to predict dynamic crack propagation in fiber composite structures is proposed. The proposed approach is based on a generalized formulation based on the Fracture Mechanics approach and Moving mesh methodology. Consistently to the Fracture Mechanics, the crack propagation depends from the energy release rate and its mode components, which are calculated by means of the ...
U. Bardi, C. Borri, A. Fossati, A. Lavacchi, and I. Perissi
Dipartimento di Chimica, Università degli Studi di Firenze, Sesto Fiorentino, FI, Italy
A Finite element model of plasma sprayed TBC’s was developed to estimate the stress induced by thermal cycling experiments. A heat transfer analysis was performed to evaluate the temperature distribution on the specimen during the cooling under an impinging air jet; temperature measurements performed with an infrared pyrometer on the cooled samples show good agreement with the evaluated ...
L. Armellin, F. Gatelli, and G. Tanghetti
R&D Department, Metelli S.p.A., Cologne, BS, Italy
Ball joints are widely used in many applications. This paper describes the contact and kinematic analysis of an Rzeppa type constant-velocity joint (CV-joint). Starting from a conveniently simplified 3D model, at fixed joint angle of 45°, a CV-joint made of all “generic steel” components has been studied. Considering only a “perfect” geometry (i.e. not affected by ...
Equation-Based Modelling: True Large Strain, Large Displacement and Anand's Plasticity Model with COMSOL's Moving Mesh Application Mode
O. Toscanelli, V. Colla, and M. Vannucci
Scuola Superiore S. Anna, Pontedera, PI, Italy
In this work the solution of the structural problem obtained by mean of the velocity approach is presented. More in detail the balance and constitutive equations are expressed in Eulerian form, the mesh is not material. The approach is general, is suitable both for material boundary or no-material boundary and for a generic material model. The Hooke's elastic model and the Anand's plasticity ...
Danish Technological Institute, Aarhus C, Denmark
The use of the finite element method for understanding and analyzing the freezing and drying processes of food products is in focus in this paper. The objective of this study is to develop a model that can predict temperature distribution and weight loss of food products during the freezing and drying processes. The problem was solved by utilizing heat, mass transfer and moving mesh model. In ...
J. Schumacher, P. Fideu, G. Ziegmann, and A. Herrmann
TU Clausthal-Institute of Polymere Materials and Plastic Engineering, Clausthal-Zellerfeld, Germany
CTC GmbH Stade, Stade, Germany
Faserinstitut Bremen e.V., Bremen, Germany
The current paper focuses on the creation of a consistent environment for the numerical prediction of the physical properties of polymer composite. A limitation factor for the successful simulation of composite processes is the correct estimation of the effective properties depending on several factors such as the constituents (fiber, polymer), the process setup. The numerical prediction of the ...
Design and Simulation of a Microscale Magnetophoretic Device for the Separation of Nucleated Fetal Red Blood Cells from Maternal Blood
G. Schiavone, D.M. Kavanagh, and M.P.Y Desmulliez
Politecnico di Torino, Torino, Italy
MIcroSystems Engineering Centre, School of Engineering & Physical Sciences, Heriot-Watt University, Edinburgh, Scotland, United Kingdom
Intense research has been carried out into methods that aim at harvesting fetal cells from maternal blood as substitutes to amniocentesis and chorionic villus sampling. This work focuses on the separation of fetal nucleated red blood cells from the maternal circulation based on their intrinsic magnetic properties. The design and simulation of a magnetophoretic separator is described, as it will ...
J. Hilgert, H. Schmidt, and J. Dos Santos
GKSS Forschungszentrum GmbH, Geesthacht, Germany
Danmarks Tekniske Universitet, Kgs. Lyngby, Denmark
Based on the example of a bobbin tool Friction Stir Welding process model a technique to model thermal processes with a moving geometry in COMSOL is introduced. The described approach allows modeling the transient temperature fields in setups that are governed by a large relative movement of different parts of the geometry. The movement of the tool is realized in a sequence of discrete time ...
VTT, Technical Research Centre of Finland, Espoo, Finland
Radionuclide transport modeling is a part of the research concerning geological disposal of spent nuclear fuel. Typically, the transport models near a single deposition hole focus on the reactions of nuclides, while the model geometry and the flow of groundwater are often simplified. In this paper, instead, a radionuclide transport model in a detailed 3D geometry with no reactions is introduced. ...
Underground Coal Fire Extinction Model Using Coupled Reactive Heat and Mass Transfer Model in Porous Media
S. Suhendra, M. Schmidt, and U. Krause
Laboratory II.2: “Flammable Bulk Materials and Dusts, Solid Fuels”, Federal Institute for Materials Research and Testing (BAM), Berlin, Germany
Green house gases emission associated with natural hazard of underground coal seam fire has been recognized as a worldwide problem leading to global warming threat. Therefore, in this paper a model to study underground coal fire is presented and the results will be devoted to strategic development of coal fire extinction technology within the framework of Sino-German Coal Fire Research ...