Presentazioni e Articoli Tecnici

In questa sezione troverete i lavori presentati alle Conferenze mondiali COMSOL. Le presentazioni descrivono ricerche e prodotti innovativi progettati con COMSOL Multiphysics da colleghi di tutto il mondo. I temi delle ricerche presentate abbracciano un'ampia gamma di settori produttivi e aree applicative, in ambito elettrico, meccanico, fluidodinamico e chimico. Lo strumento di Ricerca Rapida vi permetterà di trovare le presentazioni che si riferiscono all'area di vostro interesse.

Cross Method of Nanoscale Modeling and Macroscopic Data to Estimate Anion Effective Diffusion Coefficient in Argillite

N. Diaz1, F. Goutelard1, and P.Turq2
1CEA/DEN/DPC/SECR/L3MR, CEN Saclay, Gif-sur-Yvette, France
2LI2C, Université Pierre et Marie Curie, Paris, France

Based on a mechanistical understanding of solute migration in pure clay at nanometric scale, a model has been developed to evaluate the effective diffusion coefficient De in clay-rocks at the centimetre scale from the description of the mineralogy (and its heterogeneity) of the rock at the micrometer scale.

Modeling Solute in Clays at the Nanometric Scale Part I. Application to the Alcaline Series

N. Diaz1, F. Goutelard1, and P.Turq2
1CEA/DEN/DPC/SECR/L3MR, CEN Saclay, Gif-sur-Yvette, France
2LI2C, Université Pierre et Marie Curie, Paris, France

The argillite formation has been proposed as a potential host rock for deep radioactive waste disposal. These materials have very low permeability and diffusion is likely to be the predominant transfer mechanism for solute migration.The negatively charged surface of the clays induces unexpected behaviour of the ions: while the anions diffuse slower than HTO, the transport of the cations is ...

Electro-Mechanical Modeling of Excitable Soft Tissues

Luciano Teresi
Assistant Professor
School of Engineering
Università "Roma Tre"
Rome, Italy

Cardiac muscle exists in two forms: the contractile myocardium and specialized conducting cells that spread the wave of depolarization throughout the chambers of the heart. Action potentials are initiated in the sinoatrial (SA) node, which serve as the “pacemaker” of the heart. In this presentation, this is investigated thoroughly with different examples and simulated results of ...

Induction Heating of Samples in Vacuum Systems

A. Della Savia
SAES Getters Group, Lainate, Italy

Getter materials need to be activated in a vacuum system, where induction heating is one of the fastest processes. In this case, eddy currents generated by high frequency AC in a coil surrounding a bulb heat the materials.The temperature profile inside these items depends on geometry configurations, along with the coupling of the samples and material properties.In this article we analyze the ...

Computation of Space-Time Patterns via ALE Methods

V. Thümmler1, and A. Weddemann2
1Department of Mathematics, Bielefeld University, Bielefeld, Germany
2Department of Physics, Bielefeld University, Bielefeld, Germany

Partial differential equations which exhibit solutions that are spatial temporal patterns are often found in biological and chemical systems, e.g. when describing pattern formation in reaction-diffusion systems.Special classes of such patterns are relative equilibria and relative periodic orbits, which are solutions that in an appropriately co-moving frame of reference are stationary and ...

Modelling the Coupled Heat and Mass Transfer during Fires in Stored Biomass, Coal and Recycling Deposits

F. Ferrero
Federal Institute for Materials Research and Testing Division II.2, Berlin, Germany

It is known that in big storages of bulk materials the danger of the self-ignition is relevant (long time storages). The Consequences of uncontrolled fires include considerable CO2 emission and economical and human losses to mention a few. The understanding of this phenomena is therefore of great importance.A numerical model can be of great help in understanding such complex phenomena. In this ...

A non-Conventional use of COMSOL to Solve a Complex 3D Geometrical Problem

J. P. Caire, and F. Jomard
LEPMI, ENSEEG, Saint Martin d'Hères, France

The purpose of this study was the optimization of an industrial furnace from a thermal point of view. Such a cylindrical furnace contains an Al-Mg molten alloy covered by a KCl-NaCl molten salt layer floating on it to prevent alloy evaporation. When tilting the cylindrical furnace, it was necessary to compute the relation between the salt and alloy volumes and the area of the liquid alloy/salt ...

Robust Design of an LEM by Means of Interval Taylor Extension

B. De Vivo, P. Lamberti, and V. Tucci
Dept. of Electrical and Electronic Engineering, University of Salerno, Salerno, Italy

In this paper, the Robust Design of a Linear Electric Motor (LEM) is performed. A Robust Design is a set of nominal parameters that satisfies the customer constraints with uncertain parameters. In particular, it is possible to obtain the Most Robust Stationary Design (MRSD) of a Performance Function (PF) by looking at the minimum range of the Interval Extension of its Taylor series. Furthermore, ...

3D Finite Element Models of Ground Deformation and Stress Field in a Viscoelastic Medium

D. Scandura1,2, G. Currenti1, and C. Del Negro1
1Istituto Nazionale di Geofisica e Vulcanologia, Sezione di Catania, Catania, Italy
2Dipartimento di Matematica e Informatica, Università di Catania, Catania, Italy

A 3D finite element model was used to evaluate the time dependent ground deformation and the stress change caused by a pressure source embedded in a viscoelastic medium. In volcanic areas, the presence of inhomo-geneous materials and high temperatures produce a lower effective viscosity of the Earth's crust which calls for consideration of the thermal regime of crustal volume surrounding the ...

Quick Search

151 - 159 of 159 First | < Previous | Next > | Last