Galleria dei Modelli

La Galleria dei Modelli raccoglie un'ampia varietà di modelli realizzati con COMSOL Multiphysics in diversi ambiti applicativi, inclusi quelli elettrico, meccanico, fluidico e chimico. E' possibile scaricare i file .mph dei modelli pronti all'uso e le istruzioni step-by-step per costruirli, e utilizzarli come punto di partenza per le proprie simulazioni. Lo strumento di Ricerca Rapida permette di trovare i modelli che si riferiscono alla propria area di interesse. Per scaricare i file .mph dei modelli è necessario effettuare il login o creare un account COMSOL Access associato a un numero di licenza valido.

E-core Transformer Using Multi-Turn Coil Domains - new

This is the transient model of a single phase E-core transformer using a Multi-Turn Coil Domain. The model includes the effect of a nonlinear B-H curve in the core and shows how to connect the transformer model to the external circuits using Electric Circuit interface. The simulation is performed for two different cases; the first one with a unity turn ratio and second one with a turn ratio of ...

Shell-and-Tube Heat Exchanger - new

Shell-and-tube heat exchangers are commonly used in oil refineries and other large chemical processes. In this model, two separated fluids at different temperatures flow through the heat exchanger, one through the tubes (tube side) and the other through the shell around the tubes (shell side). Several design parameters and operating conditions influence the optimal performance of a shell and tube ...

Boiling Water - new

Boiling flow is an example of phase transition initiated by raising the temperature of a liquid above its saturation temperature. It is possible to accomplish this in many ways; in this example by applying an external heat flux to a solid surface in contact with the liquid. There are three distinct regimes that characterize boiling induced by a heated surface: nucleate, transition, and film. ...

Electrostatically Actuated Cantilever - new

The elastic cantilever beam is one of the elementary structures used in MEMS designs. This model shows the bending of a cantilever beam under an applied electrostatic load. The model solves the deformation of the beam under an applied voltage.

Flow in a Pipe Elbow - new

Water flow in a 90 degree pipe elbow. The flow is simulated using the k-omega turbulence model. The result is compared to engineering correlations.

Free Convection in a Water Glass - new

This model treats the free convection and heat transfer of a glass of cold water heated to room temperature. Initially, the glass and the water are at 5 °C and are then put on a table in a room at 25 °C. The nonisothermal flow is coupled to heat transfer using the Heat Transfer module.

Flow Past a Cylinder - new

The following model examines unsteady, incompressible flow past a long cylinder placed in a channel at right angle to the oncoming fluid. The cylinder is offset somewhat from the center of the flow to make the steady-state symmetrical flow unstable. The simulation time necessary for a periodic flow pattern to appear is difficult to predict. A key predictor is the Reynolds number, which is ...

Computing Capacitance - new

A capacitor, in its simplest form, is a two terminal electrical device that stores electric energy when a voltage difference is applied across the terminals. The stored electric energy is proportional to the applied voltage squared and is quantified by the capacitance of the device. This model introduces a model of a simple capacitor, the electric field and device capacitance are solved for under ...

Equation-Based Modeling in COMSOL Multiphysics

Partial differential equations (PDEs) constitute the mathematical foundation for describing the laws of nature. This presentation provides an introduction to customizing your simulations by developing models directly with PDEs. Learn how to add ordinary differential equations (ODEs) and algebraic equations to your model. Equation-based modeling is a powerful method eliminating the need for ...

Copper Deposition in a Trench - new

This model demonstrates the use of moving meshes in the application of copper electrodeposition on circuit boards. In these environments, the presence of cavities or 'trenches' are apparent. The model makes use of the Tertiary, Nernst-Planck interface for electrodeposition to keep track of the deformation of the mesh. Furthermore, electrochemical reaction kinetics through use of the ...

Quick Search